### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [13 March 2023 04:03 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/1 "2023-03-13T04:03:53Z")
Using the Ender 5 Plus + BigTreeTech SKR 3 profile I cannot change the steppers needed for my configuration. This board allows you to buy steppers and plug them in.
Side question: What screen does this configuration use? Is there any way to change it?
---
### Author:  [@CRCinAU](https://marlin.crc.id.au/forum/u/CRCinAU)
#### Post date: [13 March 2023 07:11 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/2 "2023-03-13T07:11:57Z")
> [@jesseclutter](#):
>
> This board allows you to buy steppers and plug them in.
Yep - you’re right. I’ve updated this in the DB.
Be aware that this functionality has not been tested at all - so I’m not sure of the outcome. Feedback would be very welcome.
> Side question: What screen does this configuration use? Is there any way to change it?
I don’t actually know - I haven’t personally tested any of the Ender 5 bits because I don’t have access to one.
There is actually some information about this on the Configurations page:
>
>
> //github.com/MarlinFirmware/Configurations/tree/bugfix-2.1.x/config/examples/Creality/Ender-5%20Plus/BigTreeTech%20SKR%203
---
### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [13 March 2023 07:27 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/3 "2023-03-13T07:27:04Z")
Okay, I did experiment with this a bit. In the readme for this configuration it says this:
## Marlin DGUS UI Instructions
The stock LCD needs to be flashed with a custom LCD firmware available from [Flashing the firmware · Desuuuu/DGUS-reloaded Wiki · GitHub](https://github.com/Desuuuu/DGUS-reloaded/wiki/Flashing-the-firmware)
But unfortunately in the attempts to get this working, the SD slot no longer works so I’m unable to flash new firmware. However, whenever I get a new board I will submit all I can to help you with this configuration.
---
### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [13 March 2023 18:29 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/4 "2023-03-13T18:29:52Z")
Feature Requests:
```auto
// Frivolous Game Options
//#define MARLIN_BRICKOUT
//#define MARLIN_INVADERS
//#define MARLIN_SNAKE
//#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu
```
These as options to enable the games on Marlin.
```auto
#define LCD_LANGUAGE **
* Select the language to display on the LCD. These languages are available:
*
* en, an, bg, ca, cz, da, de, el, el_CY, es, eu, fi, fr, gl, hr, hu, it,
* jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, sv, tr, uk, vi, zh_CN, zh_TW
```
To be given the ability to swap languages on the display.
```auto
//#define YHCB2004
//#define RADDS_DISPLAY
//#define LCD_SAINSMART_I2C_1602
//#define LCD_SAINSMART_I2C_2004
//#define CR10_STOCKDISPLAY
//#define ENDER2_STOCKDISPLAY
//#define U8GLIB_SSD1306
//#define MKS_TS35_V2_0
//#define MKS_ROBIN_TFT24
//#define MKS_ROBIN_TFT28
//#define MKS_ROBIN_TFT32
//#define MKS_ROBIN_TFT35
//#define MKS_ROBIN_TFT43
//#define MKS_ROBIN_TFT_V1_1R
//#define TFT_TRONXY_X5SA
//#define ANYCUBIC_TFT35
//#define LONGER_LK_TFT28
//#define ANET_ET4_TFT28
//#define ANET_ET5_TFT35
//#define BIQU_BX_TFT70
//#define BTT_TFT35_SPI_V1_0
```
A list of displays I saw. I’m not an expert so I wasn’t sure what the controller section meant. But a section where you can swap it would be nice.
---
### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [14 March 2023 23:36 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/5 "2023-03-14T23:36:01Z")
Hi, I got my new board and the SD card slot is working and I’m able to properly flash the firmware again. The bad news is that when I fried my board it took the screen with it. I have ordered a replacement it should be here Thursday hopefully I can make a report by then.
Side note I had tried to build the firmware on the site 3 times all as failures, no error was specified so I can’t list what’s wrong either.
---
### Author:  [@CRCinAU](https://marlin.crc.id.au/forum/u/CRCinAU)
#### Post date: [14 March 2023 23:56 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/6 "2023-03-14T23:56:17Z")
Can you post the assigned builder and the build IDs?
I can take a look at what / why it failed.
---
### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [15 March 2023 00:02 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/7 "2023-03-15T00:02:23Z")
951d893c
b75b26da
e0bf006e
I don’t see an area for assigned builder.
---
### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [18 March 2023 16:07 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/8 "2023-03-18T16:07:33Z")
Invert X stepper direction
Invert Y stepper direction
Invert Z stepper direction
So testing the configuration and messing with it in Marlin these settings should be enabled.
---
### Author:  [@jesseclutter](https://marlin.crc.id.au/forum/u/jesseclutter)
#### Post date: [19 March 2023 17:32 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/9 "2023-03-19T17:32:22Z")
| Build Reference: | d089da08 |
| --- | --- |
| Submit time: | 2023-03-19 17:31:00 UTC |
| Last Change: | 2023-03-19 17:31:21 UTC |
| Current Status: | Build Failed! |
| Builder Allocated: | dallas-builder |
| Errors: | |
No errors are showing
---
### Author:  [@CRCinAU](https://marlin.crc.id.au/forum/u/CRCinAU)
#### Post date: [20 March 2023 07:41 UTC](https://marlin.crc.id.au/forum/t/ender-5-plus-bigtreetech-skr-3-steppers-locked/1594/10 "2023-03-20T07:41:29Z")
Hmmm - it looks like this is the error:
```auto
4427 | #error "DGUS_LCD_UI RELOADED requires HOME_AFTER_DEACTIVATE to be disabled."
```
It looks like this seems to be activated by my macro for enabling BLTOUCH support.
I’ve removed this from the BLTOUCH macro - and I’ll look at adding it as a specific safety option within the builder at some point.
I’m being sent across the country from tomorrow for work, so I might not be able to look at it for a little while.